Media Library / Images

ERV SR:

ERV with inner protection sleeve of stainless steel AISI 316 Ti to prevent abrasion of the rubber liner, i. e. for media containing abrasive components or to avoid cavitation. Please note : The nominal bore is reduced.

ZVG 2 DISH nozzle for L.P. Gas / Autogas, LPG 16 hose assembly

Equipment truck for dangerous goods accidents

suitable hose assemblies and adapters from Elaflex, ELAFLEX_Information_2.17E.pdf

Manufacturing ERV flanges

Hose assemblies for LPG

with flange connection, ACME connection, NPT thread

SPANNLOC bolted safety clamps of stainless steel

SC 75 SS

Equipment truck for dangerous goods accidents, Elaflon PTFE universal hose assembly, DDC Dry Disconnect Coupling

HD 38 C NEON, Aljac bonding reel

Airfield refueller (e-refuelling technology)

TWO 100

TW coupling seal for Tank truck couplings DN 100 to EN 14420-6. NBR black.

RS 11/2 x 2 SS

Reducer Female/Male

SPANNFIX pinned Sicherheits Klemmbacken aus aluminium

SX 75 NR Al

ERV-R 100.16

RED BAND Rubber Expansion Joint for water, drinking water (DVGW W 270 as well as ACS, conform to FDA), cold and warm waste water, seawater, cooling water, also with chemical additives for water treatment, low concentrated acids and alkalis, salt solutions, technical alcohols, esters and ketones. Can be used in oily athmospheric environments, e.g. engine rooms. Temperature range - 40° C up to + 100° C, temporarily up to + 120° C. Electrically dissipative.

Vehicle refuelling with LPG (L.P. Gas, Autogas)

ZVG 2 ACME nozzle, LPG 16 hose

VR Hose Reel Spring Rewind red, ZVA Slimline 2 GR green, ZAF 2

for active Vapour Recovery (VR) for gasoline fuels

Slimline 16 black

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360.

ELAFLEX Hamburg

Assembling ERV limiters (tie rods) with spherical discs and conical seats

Universal hose assembly UTS 50 with VC 50 SS / SS

MB 80 SSE

TW dust cap of stainless steel, surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

Storz Safety Couplings Type SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.

Oasis FV103 180° Fill Valve for CNG

Sample Collection Unit

DDC-M 25 Dry Disconnect Couplings and HD hose assembly for sample collection of aircraft fuel

Type PCS 38 (Polypal Clean DN 38 mm)

SL 16 for AdBlue® (blue) hose assembly with anti-kinking sleeve, colour sleeve

ZVA Slimline 2 GR, CSB 21, SL 21 Coax

petrol station Dubai - Vapour Recovery

Manufacturing of turned parts

SPANNLOC bolted safety clamps of stainless steel

SC 75 SS

ELAFLEX Hamburg

Hose assemblies pressure testing (hydrostatic test)

Large reel, HD hose assembly, ZH 50 nozzle

Rail tanker unloading of petroleum based products

FWS PP St/St composite hose, MannTek Dry Disconnect Couplings

Manufacturing warm forged parts

Example SC 150 Spannloc clamp