Media Library / Images

Slimline 16 black

Quality petrol pump hose for gasoline and diesel fuels. Also suitable for fuels with ethanol content up to E 85 and Biodiesel up to B 30 (BIO Type up to B 100). Meets weights and measures regulations, see overleaf. Cold flexible down to - 30° C / - 22° F (LT-type down to - 40° C / - 40° F). Corresponds to EN 1360.

Fuel Grade Identification to EN 16942 standard, direct print on product badges for ZVA Nozzles

ROTEX Rubber Expansion Joints

Locomotive

Tecnopal 38

Chemical hose to EN 12115 for alkalis, acids, solutions, alcohols, polar solvents, acetates, aldehydes, esters, ketones, hot water, hot air (not oily).

ELAFLEX Hamburg

Cutting area for dispensing hose

Rubber Expansion Joint ERV-R 80.16

RED BAND expansion joints for water, drinking water (approvalDVGW W 270 as well as ACS, conform to FDA), cold and warm waste water, seawater, cooling water, also with chemical additives for water treatment, low concentrated acids and alkalis, salt solutions, technical alcohols, esters and ketones. Can be used in oily athmospheric environments, e.g. engine rooms. Temperature (depending on medium) - 40° C up to + 100° C, temporarily up to + 120° C. Electrically dissipative.

Ferrule threaded hose coupling M 19-1" Ms

for petrol station dispensing hoses

Quality in the detail: valve assembly of a ZVA Slimline 2 petrol station nozzle

KR 50 - 21/2"

Filling of Heating Oil Tanks: New Adapter for difficult-to-reach house connectors

SG 3" Rg

Sight Glass with 3" female/male BSP thread, gunmetal

Slimline quality dispensing hose for the forecourt

SL 21 red

ZVG 2 DISH

Nozzle for L.P. Gas / Autogas, with 'Italian' Claw Coupling. Pictured: coupling open / closed

ZVA Slimline 2 GR, special type with bellows, black, guard 3 - side view

ZVA Slimline 2

LPG road tanker loading with MannTek SBC Safety Breakaway Couplings

Polypal Clean hose assembly

Pharmaceutical production

ZVA Slimline 2 GR

blue scuffguard, blue produc sleeve, guard no. 4

MannTek Safety Breakaway Coupling SBC 80 SS F

with flange connection

Large reel, HD hose assembly, ZH 50 nozzle

ERV-G 1000

'Yellow Band' Rubber Expansion Joint - for petroleum based products

Fixed Flange and hose tail of stailess steel

FFC 63.16 SS

ERV TAS:

ERV with PTFE lining and PTFE vacuum support ring. Properties like type TA, but also suitable for vacuum service, up to 70° C.

Road tanker with hose reel spring rewind blue, ZVA Slimline 2 green

Mobile refuelling

Cylinder Valves (Tank Heads)

TH104

Manifold for filling chemical tanktrucks

UTS hose assemblies

VB 80 SSE

TW dust plug of stainless steel, surface in contact with the medium additionally coated with Teflon® PFA. This type is used if stainless steel does not have a sufficient chemical resistance (i.e. for hydrochloric acid and iron-III-chloride) and polypropylene is not possible because of insufficient stability. Available in all standard sizes.

Hose assemblies

for petroleum based products, chemicals, foodstuff and pharmaceuticals, LPG

Ship loading various media - STW 150 and UTS 150 hose assemblies

GasGuard GG11R

The GasGuard GG11 Back-Check Valve (GG11R: with additional release screw) should be standard equipment for any LPGas road tanker operator. It is used in conjunction with LPGas bulk refueling nozzles to contain leaks at storage tank fill points. If the fill point proves to be leaking when removing the nozzle it can be left on the tank until corrective action is taken. The driver can move to the next fill point without delay.

Storz Safety Coupling SHK

upon uncoupling, the safety dust plug first falls into holding claws, relasing an eventual pressure within the system. Only then the dust cap can be fully taken off. - increased protection for the operating personnel. Easy to use, no additional pressure release necessary, slim design, does not build up, no freezing up in the dome section.